Are you looking for:

ESCO 10498 Jack Stand Flat Top - 3-Ton (Rubber Top)

ESCO 3-Ton Performance Jack Stand

  • Includes Removable Rubber Flat Top
  • 10 Adjustable Positions
  • Circular base pads for maximum stability
  • European design
  • Capacity: 3 Tons
  • Min. Height: 13.2"
  • Max. Height: 21.5"

Sold individually.

Swing Down Step 3-Step Single Handle w/ Adjustable Stake (Flat Black)

The Swing Down Step flatbed ladder is especially useful on flatbeds and dump trucks where easy and safe access has always been a problem. Thanks to its universal design, it can be mounted anywhere you can mount a pocket.

FEATURES & BENEFITS:

  • Built-in Grab Handle
  • 2-Way Gas Spring allows for controlled movement up and down
  • Adjustable Model fits all standard pockets
  • Can be padlocked in place
  • Approximately 39" long step section brings it close to the ground for easy access
  • Special tread design provides sure traction
  • Design allows three point contact
  • Latches securely in upright position when not in use
  • Easily moved from vehicle to vehicle
  • Easily installed on new or existing vehicles
  • Heavy Duty steel construction for long life
  • Black powder coat

NSN 2541-01-531-4064

Swing Down Step 3-Step Single Handle Solid Stake and Mounting Bracket

The Solid Stake Swing Down Step flatbed ladder is especially useful on flatbeds and dump trucks where easy and safe access has always been a problem. Thanks to its universal design, it can be mounted anywhere you can mount a pocket.


FEATURES & BENEFITS:

  • Built-in Grab Handle
  • 2-Way Gas Spring allows for controlled movement up and down
  • Can be padlocked in place
  • Approximately 39" long step section brings it close to the ground for easy access
  • Special tread design provides sure traction
  • Safety yellow powder coat finish
  • Design allows three point contact
  • Latches securely in upright position when not in use
  • Easily installed on new or existing vehicles
  • Heavy Duty steel construction for long life
  • Scorpion Jacks PJ25 25,000 lb. Capacity Pit Service Jack

    The Scorpion PJ25 Pit Jack is designed for use in heavy truck service pits or can also be used on above ground alignment ramp systems (Hunter & Bee-Line).


    The PJ25 will fit virtually any pit application due to the compact design (only 34" wide and expandable to 42" wide).


    These jacks are designed to lift the vehicle across the axle using the lifting saddles provided (Low/Med/Hi).


    Features

  • 25,000 lb capacity
  • Dual Hydraulic rams for lifting
  • Lift over 20" with a built in safety lock
  • Convenient pull handle, powder coat paint & zinc plated components
  • Lift across the axle with the lifting saddles or lift on the frame
  • Heavy-Duty hydraulics and air motor
  • Special roller bearing wheels allow for effortless rolling
  • Express Mobile - Light and Air Brake System Tester

    Make your service truck investment as productive as possible with an Express Mobile and eliminate most of the walking associated with trailer servicing. you can easily check all lighting functions and the air brake system (including brake adjustment) in just two minutes, start to finish. That's 20 trailers per hour including set-up, disconnect and all walk-time!


  • Designed to be mounted in your service truck. Perfect for on-site trailer readiness inspection
  • Radio remote-controlled air brake tester saves tons of time.
  • Built in Scanner lighting tester operates lights in sequence. Check them all in a single walk around
  • Test airbrake and lighting functions in minutes
  • Integral mounting flanges make installation a snap!
  • Sourced by your service truck's electrical and service air systems
  • User supplied air hoses and trailer cable
  • Includes spare remote
    General Specifications
    Scope of Equipment Trailer lighting systems testing using a circuit scanning sequence with trailer air brake testing using radio remote-controlled air actuation from behind the trailer. Unit is designed for mounting in a service truck.
    Model Designation 01011
    Dimensions 14.88"H x 16.18"W x 5.38"D overall, including mounting flanges
    Cabinet 16-gauge steel, base pan 14-gauge. Weldment forms basic structure. Black winkle finish.
    Mounting Integral mounting flanges on the back and bottom of the cabinet for mounting to floor or interior sidewall of service truck.
    Environmental Weather, dust, oil, overspray, and dirt resistant. Not intended to be mounted outside of the service body
    Light / Electrical Testing Equipment
    Light Testing Equipment Complete built-in Scanner trailer light tester as described below
    Operating Voltage 12 vdc (nominal)
    Wiring Protocol SAE 7-Wire
    Scanned Circuits Left turn (1.5 sec), stop (3.0 sec), right turn (1.5 sec). Circuits are powered one at a time, and the sequence repeats indefinitely
    Freeze feature "Mode Select" switch starts and stop scanning action as needed. Has center "all off" position
    Switched Circuits "On-Off Toggle" switches control aux, marker, and tail light circuits
    Circuit Status Indicator One red LED for each of the six circuits
    Low Battery Indicator One red LED blinks at 11 volts, on steady at 10 volts
    Circuit Breakers Aux, mark, tail - one 20 amp auto-reset circuit breaker. Left, stop, right - one 15 amp auto-reset circuit breaker
    Short Circuit Warning One LED for 20 amp breake, one LED for the 15 amp breaker
    Current Capacity 34 amps total
    Trailer Connection SAE 7-Pole socket mounted on cabinet. Light cord and plugs not provided. these vary with the specifics of each installation
    Power Supply 12 vdc provided by service truck. Requires connection to truck battery's positive terminal, a good ground connection, and connection to the truck's accessory feed (the latter is not a strict requirement but is strongly recommended)
  • Loading...