Are you looking for:

Automotive Battery Conductance/Electrical System Analyzer
Features and Benefits:
  • Conductance Technology advantages make battery testing safe, fast and simple
  • Proven test algorithms - also displays available power in CCAs ath the end of each test
  • High and low voltage capture for improved starter/charger system testing
  • Tests discharged batteries
  • Proven reliability and durability
With an innovative design made in the USA, this analyzer features endorsed or required technology by virtually every automotive OEM. Building upon the success of the PBT-100, the first battery conductance tester built for the professional technician's toolbox, the PBT200 offers these additional capabilities: shows available power in CCA in addition to condition and voltage, bad cell detection, advanced starter testing - down arrow displays the captures low voltage from cranking the engine for simple starter analysis. Advanced starter testing - using the up and down arrows while the engine is running displays the captured high and low voltage for simple alternator/regulator analysis.

Premium Automotive Digital Multimeter with IR Thermometer

Features and Benefits:

  • CAT III 1000 Volt rated - safe to use with Hybrids
  • 1 Ms Peak Min/Max function for glitch capture
  • Desirable 20 Amp Fused Test Range
  • Designed for advanced automotive diagnostics
  • Includes EST-100 IR Thermometer with 8 to 1 distance ratio

For automotive, marine, small engine, HVAC and Industrial technicians this is the highest quality Auto-ranging DMM designed for automotive trouble shooting. Provides 18 test functions, 48 test ranges. Modern design with the protective holster built into the housing.Data hold, auto power-off, + trigger adjust. Large LCD display with white LED backlighting and 40 segment analog bargraph. The ESI597 kit includes IR Thermometer, test leads, Inductive RPM pick-up, temperature probe, 9 volt battery, instructions manual and hard storage case.  Inductive RPM pick-up features a five position, adjustable sensitivity switch.

Scorpion Jack TJ12 Stationary 25,000 lb. capacity Truck Jack

The Scorpion Installed In-Ground lift is semi-recessed in your shop floor. This is a semi-inground installation is an ideal solution for those shops that perform a lot of tire service and Brake Service. This is an installed version of the ScorpionTJ12 service jack and it offers a perfect combination of speed, efficiency, ease of use and value. The Scorpion Installed lifts are much less expensive than your standard above- ground options or for that matter the in-ground options too.


These jacks are designed to lift the vehicle across the axle using the lifting saddles provided (Low/Med/Hi). So you lift the whole front end or axle assembly in one go. There is a tire spotting dish for quick set up, and a remote control to allow the operator to check the load.


There is a built in lock for safety and other convenience features.


The lifts come with a control station housing the pump unit and a 20 Ft. Remote control so the operator can spot the load.


Features:

  • 25,000 Lb capacity
  • Dual hydraulic rams for lifting
  • Lift over 20" with a built in safety lock
  • Lift across the axle with the lifting saddles or lift on the frame
  • Heavy-duty hydraulics and air motor

  • Choose between:

  • Above Ground install - 8" Driver Over Height
  • Semi In-Ground install - 4.25" Drive Over Height
  • In-Ground Install - Flush mount with 0" Driver Over Height
  • Dump-Lok - Dump Body Safety Stand (Flat Top - 4-7/16 in Frame)

    Dump-Lok dump bed braces are an engineering breakthrough in the workplace. Dump-Lok dump bed braces safely hold dump boxes at angles higher than most manufacturer body props, giving workers safe access to more areas underneath the dump bed.

    • Sold As A Pair. Intended to be used as a pair
    • Used Universally on any brand dump box
    • Equipped with high grade, high tensile steel chains to further ensure safe repairs
    • Flat Top Model for offset frame beds and trailers
    • Fits up to 4-7/16" flange - 3-1/2 is standard

    OSHA has issued citations to employers for failing to provide lockout procedures while employees were working under the dump body of dump trucks. They have recognized the hazard of unsecured dump beds and have recommended using an alternative "truck bed brace bracket".

    • Overall Height: 21"
    • Overall Width: 6"
    • Overall Length: 12.75"
    • Maximum Capacity (pair): 50,000 lbs
    Tiger Tool Gunite, Brunner, Bendix Slack Adjuster Puller

    Fits virtually all Gunite, Brunner, and Bendix self-adjusting slack adjusters

  • High strength ADI and steel castings
  • CNC machined, billet 4140 forcing screws
  • Grade 8 attaching hardware
  • Eliminates dangerous hammering and cutting torch methods
  • Designed for high capacity pull. can be used with 1/2" impact wrench
  • Simple to slip on for instant results

  • Loading...