Are you looking for:

Scorpion Jack TJ12 Stationary 25,000 lb. capacity Truck Jack

The Scorpion Installed In-Ground lift is semi-recessed in your shop floor. This is a semi-inground installation is an ideal solution for those shops that perform a lot of tire service and Brake Service. This is an installed version of the ScorpionTJ12 service jack and it offers a perfect combination of speed, efficiency, ease of use and value. The Scorpion Installed lifts are much less expensive than your standard above- ground options or for that matter the in-ground options too.


These jacks are designed to lift the vehicle across the axle using the lifting saddles provided (Low/Med/Hi). So you lift the whole front end or axle assembly in one go. There is a tire spotting dish for quick set up, and a remote control to allow the operator to check the load.


There is a built in lock for safety and other convenience features.


The lifts come with a control station housing the pump unit and a 20 Ft. Remote control so the operator can spot the load.


Features:

  • 25,000 Lb capacity
  • Dual hydraulic rams for lifting
  • Lift over 20" with a built in safety lock
  • Lift across the axle with the lifting saddles or lift on the frame
  • Heavy-duty hydraulics and air motor

  • Choose between:

  • Above Ground install - 8" Driver Over Height
  • Semi In-Ground install - 4.25" Drive Over Height
  • In-Ground Install - Flush mount with 0" Driver Over Height
  • Goodall 20 ft. 2 Gauge, 500 Amp (14-202)

    Heavy-Duty 2-Gague 500 Amp

  • Twin extruded jacket
  • Cable remains flexible to -40 degree F
  • Replaceable jaws, all copper wire
  • 15 ft
  • 19" Slide-Away Step 2-Step Bolt On

    These retractable steps are a must for any trailer. Featuring the self-cleaning grating with a serrated leading edge, the Slide-Away Step offers superior traction. Eliminates the use of slippery ICC bumper. Easily deploys and stows in seconds. Standard powder coat red for high visibility.

    Weight capacity of 350 lbs.


  • Mfr Part # DB0201
  • Bolt on 2-step
  • Width: 19-1/4"
  • Stair Width: 14-1/2"
  • Tread Depth: 6-1/16"
  • Closed Length: 20"
  • Open Length: 33"
  • Bolt-On with Brackets 14 1/2"W x 22"L
  • Goodall: 12/24 Volt AntiZap Surge Permanent Mount

    Eliminates the need to disconnect the battery from the terminals while welding on a vehicle. Simply clip on the Antizap Surge Protector and you’re ready to weld. Protects sensitive electronics, reduces labor time and pays for itself after one or two uses.

    • Protects vehicle electronics during MIG, TIG, or Argon Arc welding
    • Fully insulated booster clamps with 2-function Antizap protection
    • Eliminates the time needed to disconnect the battery
    • Just clip the clamps across the battery and the green LED indicates complete electrical system protection

    ENSURE YOUR VEHICLE IS CORRECTLY GROUNDED BEFORE WELDING.

    The Antizap Surge Protector will not protect against induced current created by incorrect welding procedures. Always follow manufacturer’s instructions. Additional Antizap surge protection may be required for accessories wired into the vehicle’s wiring harness between the point of weld and the battery. If in doubt, seek the advice of an electrician prior to welding. Goodall Mfg.’s warranty is limited to the replacement of a defective product. Goodall shall not be liable for any consequential or incidental damages.

    NE-77 Noise Eliminator
    "Noise Eliminator" Microphone Durable, noise eliminating microphone for use with the Model 777 Leak Detector Easy to use accessory for leak detection in high, outside noise situations Engineered to improve success during difficult conditions: PVC pipe, through asphalt or pavement, and water filled cavaties Designed for "stand-up" operation Will effectively muffle outside encompassing noise, such as; wind, construction, and vehicle traffic Will plug into any Goldak Model 777 Leak Detector!
    Loading...